Electrical Grounding and Shielding Electronic Systems – PASTI JALAN

Electrical Grounding and Shielding Electronic Systems

Hotel All Season Jogjakarta |  5-7 March  2013 |  IDR 7.500.000,-/participant   – PASTI JALAN




ABSTRACT

This course stresses the fundamental electromagnetic compatibility principles involved in typical grounding and shielding problems. Understanding the objectives and techniques for grounding and shielding will reduce misconceptions and allow a more systematic approach to replace trial and error methods. For example, the course explains why a signal ground is not the same as a signal return.

Also, solutions for the numerous problems caused by wiring inductance are described and demonstrated. The course emphasizes the development of logical diagnostic techniques for identifying various types of noise problems. Often, the correct identification of the problem is more difficult than the solution. The course is at an introductory level; however, some knowledge of electronic circuits and system design is assumed. Several interference mechanisms and shielding techniques are demonstrated.

               

COURSE CONTENT

 

I. Basic Principles of Noise Reduction

  1. Importance of wiring inductance
  2. Bandwidth of pulse waveforms
  3. Noise coupling mechanisms
  4. How to identify the mechanism
  5. Common and differential modes

II. Grounding: Why and How?

  1. What is electrical ground?
  2. Reasons for grounding
  3. Signal ground, signal return
  4. Ground grid technique
  5. Isolated grounding technique
  6. Ground loop noise reduction

III. Signal Ground Techniques

  1. Ground each current only once
  2. Unsafe signal grounding
  3. Single point versus ground grid
  4. Signal isolation techniques

IV. How to Diagnose Noise Problems

  1. Ringing, rounding, and reflections
  2. Effects of signal impedance distribution on susceptibility
  3. Practical diagnostic techniques
  4. Noise coupling examples

V. Noise Reduction Techniques

  1. Filtering and shielding
  2. Reducing mutual inductance

VI. Filtering Conducted Noise

  1. CM and DM filter techniques
  2. Improving circuit balance
  3. 1 GHZ filtering techniques
  4. DC power bus design

VII. Inductive and Capacitive Shielding

  1. Self-shielding techniques
  2. Misuse of twisted pair
  3. Grounding cable shields
  4. Shielding examples

VIII. Reducing Electromagnetic Coupling

  1. Identifying EM coupling
  2. Controlling CM currents

 

OBJECTIVE

This course is designed to enable participants to:

  • Define electrical ground, signal ground, and signal return
  • Describe various grounding techniques
  • Diagnose noise problems
  • Identify methods to reduce and filter noise
  • Define inductive and capacitive shielding
  • Describe techniques for reducing electromagnetic coupling
  • Select appropriate cabling
  • Identify methods to ensure impedance matching
  • Identify noise coupling mechanisms

WHO SHOULD ATTEND

This course is recommended for electrical engineers, technicians, designers and release engineers responsible for electronic or electromechanical products.

INSTRUCTORS

Ir. Teguh Santoso  ( cv Attached)

Ir. T. Haryono, M.Sc., CEng MIEE ( CV. Attached)

VANUE AND DATE

Vanue    : Hotel All Season Jogjakarta
date        : 5-7 March  2013

Course Tution :

 IDR 7.500.000,-/participant non residential. For send 3 person. IDR. 6.500.000,-/Participant Nonresidential

 FASILITAS

  • Meeting Room Hotel ***
  • Training KIT
  • Souvenir
  • Sertifikat
  • Flash disk 4 GB + soft and hard copy materi
  • 2 X Coffe Break + Lunch

 

Formulir Permintaaan Informasi Lanjutan / Pra-Pendaftaran Public Training
  1. INFORMATION OPTIONS
  2. (required)
  3. (required)
  4. PERSONAL DATA
  5. (required)
  6. (required)
  7. (required)
  8. (valid email required)
  9. (required)
  10. (required)
  11. PRE REGISTRATION DATA (Tidak Mengikat)
  12. (required)
  13. MESSAGE FOR TRAINING PROVIDER
  14. Captcha
 

cforms contact form by delicious:days