OIL & GAS: MEASUREMENT AND CALCULATION

Training measurement and calculation oil & gas ini menyajikan prinsip, desain dan aplikasi sistem pengukuran aliran, menekankan akurasi flowmeter

Bandung | 02 – 04 September 2020 | Rp 7.950.000/ peserta
Bandung | 05 – 07 Oktober 2020 | Rp 7.950.000/ peserta 
Bandung | 02 – 04 November 2020 | Rp 7.950.000/ peserta

Jadwal Training 2020 Selanjutnya …

 

 

OIL & GAS: MEASUREMENT AND CALCULATION TRAINING INTRODUCTION AND OBJECTIVE

This training presents the principles, design, and applications of flow measurement systems, emphasizing flowmeter accuracy, performance, sizing, and specification, selection, and installation practices with objectives as follows :

  • To design a system to make practical and precise industrial flow measurements
  • To Calculate the effects of fluid properties on flow meter performance
  • To Evaluate flow meter performance statements and compare them with application requirements
  • To Specify and select the appropriate flow meters for different applications
  • To Identify requirements for flow meter calibration
  • To Solve typical flow meter problems
  • To Perform flow meter compensation and totalization calculations
  • To Understand flow and related phenomena (piping hydraulics, Reynolds Number, cavitation, etc.)
  • To Size flow elements for specific applications

 

OIL & GAS: MEASUREMENT AND CALCULATION TRAINING OUTLINE

1. Introduction to Flow Measurement
2. Flow meter Selection
3. Flow meter Performance
4. Linearization and Compensation
5. Totalization : Differential Pressure Flow meters
6. Orifice Plate Flow meters

a. Installations
b. Sizing and calculation
c. Accuracy and rangeability
d. Types and selection
e. Performance

7. V-cone Flow meters
8. Venturi tube Flow meters : Velocity Flow meters
9. Turbine Flow meters

a. Operation theory
b. Installation
c. Design and construction
d. Accuracy
e. Sizing and selection

10. Ultrasonic Flow meters

a. Operation theory
b. The Doppler effect
c. The transit time
d. Design variations
e. Application and performance

11. Magnetic Flow meters

a. Operation theory
b. Installation
c. Excitation
d. Tubes and liners
e. Electrodes
f. Selection and sizing

12. Vortex Flow meters

a. Operation theory
b. Installation
c. Sizing and accuracy
d. Limitations
e. Mass Flow meters

13. Coriolis Mass Flow meters

a. Operation theory
b. Installation
c. Sizing and accuracy
d. Limitations

14. Thermal Flow meters
15. Positive Displacement Flow meters:

a. Helical Gear
b. Oval Gear
c. Piston and Other Technologies

16. Discussion and cases study

 

TRAINING INSTRUCTOR

Dr.Ir. Sudjati Rachmat, DEA. and Team

Dr.Ir. Sudjati Rachmat, DEA. adalah dosen di jurusan perminyakan ITB sejak tahun 1979 sampai sekarang. Beliau alumnus dari ITB lulus tahun 1977, kemudian melanjutkan pendidikannya di Diplome d’Etude Approfondie Ecole Centrale de Lyon, UCB Lyon I, FRANCE. Dan pada tahun 1985 – 1987 beliau mengambil program Docteur en Mecanique de Fluide (Methode Numerique) Ecole Centrale de Lyon, UCB Lyon I, FRANCE.  Dr. Sudjati Rachmat sering menjadi instruktur dalam banyak pelatihan yang berkaitan dengan perminyakan untuk perusahaan di seluruh Indonesia, diantaranya seperti Pertamina, Chevron, Badak LNG, Total, Vico, Mobil Oil Indonesia, Ministery of Mining and Energy, Unocal Indonesia, Lemigas, IATMI-IWPL Migas, PPTM Migas, PT Caltex Pacific Indonesia, Gulf, Arco, dll.   Topik-topik training yang Beliau sampaikan diantaranya adalah production surface and down hole equipment, Basic Reservoir Engineering, Sucker Rod Pumping Theory and Practice, Production Logging Engineering, Nodal Analysis and Production Optimization, Well Test, Operation and Interpretation, Well Design, Completion and Workover, Numerical and Statistical Method for Petroleum Engineering Problems, Oil-Well Stimulation, Hydraulic Fracturing, Statistics for Petroleum Engineering, Reservoir Simulation for Enhanced Oil Recovery, Applied Reservoir Engineering and Reservoir Simulation, Aspects of Horizontal Well Technology, Geology and Geophysics Modeling, Advanced Programming on Numerical Analysis and Industrial Information System, Management Information System, Well Stimulation of Oil and Gas Reservoir, Horizontal Well Technology, Transportation of Oil and Gas, Sand Control Technology, dan lain-lain.  Beliau banyak melakukan penelitian di bidang MIGAS dan telah mempublikasikan dan menseminarkannya di forum dunia.

 

TRAINING VENUE

Bandung (Golden Flower, Banana Inn, Serela, Gino Feruci), Amaroossa Hotel, Noor Hotel, Grand Setiabudi Hotel, dll

 

DURASI TRAINING 

3 hari

 

JADWAL TRAINING 2020

  1. 02 Sep 2020-04 Sep 2020
  2. 05 Okt 2020-07 Okt 2020
  3. 02 Nop 2020-04 Nop 2020
  4. 02 Des 2020-04 Des 2020

 

INVESTATION PRICE/ PERSON

  1. Rp 7.950.000/person (full fare)  or
  2. Rp 7.750.000/person (early bird, payment 1 week before training)  or
  3. Rp 7.500.000/person (if there are 3 or more participants from the same company)

 

FACILITIES FOR PARTICIPANTS

  1. Training Module
  2. Flash Disk contains training material
  3. Certificate
  4. Stationeries: NoteBook and Ballpoint
  5. T-Shirt
  6. Backpack
  7. Training Photo
  8. Training room with Full AC facilities and multimedia
  9. Lunch and twice coffeebreak every day of training
  10. Qualified Instructor
  11. Transportation for participants from hotel of participants to/from hotel of training – VV (if minimal participants is 4 persons from the same company)

 

OIL & GAS: MEASUREMENT AND CALCULATION

 

Formulir Permintaaan Informasi Lanjutan / Pra-Pendaftaran Public Training
  1. INFORMATION OPTIONS
  2. (required)
  3. (required)
  4. PERSONAL DATA
  5. (required)
  6. (required)
  7. (required)
  8. (valid email required)
  9. (required)
  10. (required)
  11. PRE REGISTRATION DATA (Tidak Mengikat)
  12. (required)
  13. MESSAGE FOR TRAINING PROVIDER
  14. Captcha
 

cforms contact form by delicious:days