By March 12, 2014 0 Comments Read More →

INDUSTRIAL METROLOGY

INDUSTRIAL METROLOGY
Bandung | 05 – 08 Mei 2014 | Rp 7.950.000,-/peserta
Bandung | 23 – 26 Juni 2014 | Rp 7.950.000,-/peserta
Bandung | 01 – 04 September 2014 | Rp 7.950.000,-/peserta
Bandung | 14 – 17 Oktober 2014 | Rp 7.950.000,-/peserta
Bandung | 25 – 28 November 2014 | Rp 7.950.000,-/peserta


 

LATAR BELAKANG :

Hampir semua jenis industri ditemukan tingkatan-tingkatan untuk mencapai keberhasilan dalam proses pembuatan produk atau mesin dan peralatan mulai dari taraf penentuan jenis produk sampai ke taraf perawatan purnajual mesin. Pada tingkatan pembuatan dan perakitan, pemeriksaan kualitas geometrik dilaksanakan pada produk hasil dari salah satu proses produksi untuk mencegah menurunnya mutu karena keluarnya geometrik produk dari batas-batas toleransinya. Hasil pemeriksaan dibandingkan dengan spesifikasi geometrik yang tercantum pada gambar teknik. Pada taraf ini diperlukan penguasaan teknologi yang terkait yaitu metrologi geometrik.

Untuk mendukung sistem produksi yang memadai diperlukan tenaga kerja yang handal atau peningkatan keahlian tenaga kerja profesi Metrologi Industri atau Geometrik (Industrial Metrology).

SIAPA SEBAIKNYA MENGIKUTI TRAINING INI ? :

Para praktisi tingkat operator, tingkat penyelia atau perencana bidang penjaminan mutu (quality assurance) pada industri manufaktur.

TUJUAN TRAINING :

Setelah mengikuti pelatihan ini para peserta diharapkan memiliki pemahaman lebih tentang konsep dasar metrologi industri (geometrik), dan keahlian melakukan pemilihan metoda dan alat ukur yang cocok untuk pengukuran karakteristik geometrik produk.

CAKUPAN MATERI TRAINING :

1.   Konsep dasar metrologi industri.

  • Jenis dan cara pengukuran, konstruksi dan sifat umum alat ukur, kesalahan sewaktu proses pengukuran, dan analisis data pengukuran dengan metoda statistika.

2.   Pengukuran linier langsung.

  • Pengukuran linier langsung: mistar ukur, mistar ingsut/jangka sorong, mikrometer, beberapa jenis mistar ingsut dan mikrometer, dan pengukuran linier tak langsung: gauge block, dial indikator, kaliber, dan praktek pengukuran dengan alat ukur linier.

3.   Pengukuran sudut dan ketegaklurusan.

  • Busur bilah (bevel protractor), alat ukur sinus, batang sinus (sine bar), senter sinus (sine center), dan pengukuran sudut tak langsung dengan alat bantu bola, pemeriksaan ketegaklurusan, alat ukur ketegaklurusan, dan praktek pengukuran sudut dan ketegaklurusan.

4.   Metrologi elemen geometrik ulir.

  • Definisi profil ulir, kesalahan pada profil ulir, toleransi dari ulir, pengukuran elemen geometrik ulir luar: pengukuran diameter mayor ulir luar, pengukuran jarak pits ulir luar, pengukuran diameter pits dengan metoda tiga kawat, pengukuran dengan profile proyektor untuk ukuran ulir kecil, dan praktek pengukuran elemen geometrik ulir.

5.   Metrologi elemen geometrik roda gigi.

  • Profil roda gigi lurus, toleransi roda gigi lurus, pengukuran elemen geometrik roda gigi lurus, pengukuran diameter puncak, pemeriksaan kualitas bahan roda gigi, pemeriksaan kesalahan tebal gigi menggunakan mistar ingsut roda gigi (gear tooth caliper), pemeriksaan kesalahan tebal gigi menggunakan alat bantu rol, dan praktek pengukuran elemen geometrik roda gigi.

6.   Pengukuran kelurusan.

  • Pendatar (spirit level, waterpas), kalibrasi pendatar, penyetelan posisi horizontal meja rata, pengukuran kelurusan meja rata dengan pendatar dengan dudukan dua rol, pengukuran kelurusan meja rata dengan pendatar dengan dudukan autokolimator (metoda pantulan langsung, metoda pemantul sudut (corner mirror), analisis hasil pengukuran kelurusan.

7.   Pengukuran kebulatan.

  • Pengukuran kebulatan sederhana (mikrometer, kaliber ring, mikrometer tiga kaki, blok – V dan jam ukur, dudukan dua senter dan jam ukur), alat ukur kebulatan representatif (dengan meja berputar dan sensor berputar), arti dari grafik pengukuran dan parameter kebulatan, dan praktek pengukuran kebulatan.

8.     Pengukuran kekasaran permukaan.

  • Permukaan dan profil, parameter kekasaran permukaan, harga kekasaran permukaan, pengukuran kekasaran permukaan (pengukuran kekasaran rata-rata aritmetik; Ra, pengukuran kekasaran permukaan maksimum; Rt, penggambaran grafik kekasaran permukaan, analisis grafik kekasaran permukaan)

9.     Kalibrasi alat ukur dimensi.

  • Kalibrasi mistar ingsut skala nonius: pemeriksaan kelurusan sisi sensor, pemeriksaan kebenaran skala utama, dan kalibrasi mikrometer: pemeriksaan kedudukan nol, pemeriksaan kerataan dari muka ukur, pemeriksaan kesejajaran dari muka ukur, pemeriksaan kebenaran skala utama, dan praktek kalibrasi alat ukur linier

Trainer

SUGENG ISDWIYANUDI, Ir. MT. And Team
was graduated from politeknik  universitas brawijaya malang for his diploma in mechanical engineering majoring on mechanical maintenance and repairing, from ITS Surabaya for his bachelor in mechanical engineering majoring on production engineering, and from ITB Bandung for his master program in mechanical engineering majoring on production engineering. Now he is as lecturer at mechanical engineering Politeknik Negeri Bandung(before as poltek ITB). Ir. Sugeng Isdwiyanudi, MT. has followed many trainings/courses to improve his competence. He is active instructor who often deliver training for industrial participants in Indonesia, many topics he teachs in training e.g.: pump and piping, Operation and Maintenance Boiler, Operator pressure vessel 1 (cooperated with Depnaker RI), Operation and Maintenance Centrifugal Pump, Effective Shutdown Maintenance, Reliability Centered Maintenance, Advanced Reliability Performance and Hidden Failure Supporting, Management Inventory Control, Alignment, Balancing, and Vibration, Rotating Equipment: Operation and Maintenance, Material technique, Oil Analysis, Maintenance Management (Preventive and Predictive Maintenance),Heavy Equipment Maintenance, Basic Mechanical, Strength of Material, Electro Pneumatic and Hydraulic, Rotating Equipment Alignment and Vibration, Operation and Maintenance Diesel Engine, Operation and Maintenance Boiler, Operation and Maintenance Pump and Compressor, Pressure Vessel and Tank, Preventive and Predictive Maintenance, Total Productive Maintenance (TPM), Heavy Equipment Maintenance Management, Maintenance Equipment Management for Mining, Modern Maintenance and Spare Part Management System, NDT and Quality Assurance, Integrated Material Management, Effective Production Management, Plant Life Management through Reliability Based Inspection, Maintenance Planning, Scheduling, and Coordination, Integrated Maintenance Management and Control, Implementation RCM and RBI in Industries, Total Productive Maintenance (TPM), Reliability Centered Maintenance (RCM), Operator Routine Daily Checklist and Driven Reliability, Measuring, Monitoring, and Analysis of Machinery Vibration, Vibration Prevention and Monitoring System, Advanced Application of CSI 2120/2130 and AMS Suite (RBM) for Condition Monitoring and Troubleshooting, Root Cause Failure Analysis (RCFA), NDT and Quality Assurance, Piping System.  In campus he teachs for some subjects e.g.: industrial metrology, quality control, Instrumentation and measurement, machining technique, production system and quality control, Pneumatics and hydrolics, measurement system, measuremen technique(Metrology of Geometry), mechanics vibration, management of production process, product quality control, statistics application in mechanical engineering, machining process technology, Practice of industrial metrology, pneumatics control system. In campus he has many experiences e.g.: as head of Laboratory industrial Metrology POLBAN, as head of Laboratory Metrology POLBAN, as director SPMU TPSDP POLBAN (ADB Loan 1792-INO), director assistant administration and finance SPMU TPSDP POLBAN (ADB Loan 1792-INO), head of production research group POLBAN, head of department mechanical engineering P4D, department secretary of mechanical department P4D, head of Laboratory Pneumatics and Hydrolics P4D. He invites industrial participants to share and discuss in his training class..

VENUE : 

Bandung (Golden Flower, Banana Inn, Grand Seriti, Carrcadin, Amaroossa, Grand Serela, Gino Feruci, Verona Palace, Malaka, Zodiac Taurus)

 

TRAINING DURATION :

4 days

 

TRAINING TIME :  

  1. 27 – 30 Januari 2014
  2. 11 – 14 Maret 2014
  3. 5 – 8 Mei 2014
  4. 23 – 26 Juni 2014
  5. 1 – 4 September 2014
  6. 14 – 17 Oktober 2014
  7. 25 – 28 November 2014

 

INVESTATION PRICE/PERSON :

  1. Rp 7.950.000/person (full fare)  or
  2. Rp 7.750.000/person (early bird, payment 1 week before training)  or
  3. Rp 7.500.000/person (if there are 3 or more participants from the same company)

 

 

 

FACILITIES FOR PARTICIPANTS:

  1. Training Module
  2. Flash Disk contains training material
  3. Certificate
  4. Stationeries: NoteBook and Ballpoint
  5. T-Shirt
  6. Backpack
  7. Training Photo
  8. Training room with full AC facilities and multimedia
  9. Lunch and twice coffeebreak everyday of training
  10. Qualified instructor
  11. Transportation for participants from hotel of participants to/from hotel of training (if minimal number of participants from one company is 4 persons)

 

 

Formulir Permintaaan Informasi Lanjutan / Pra-Pendaftaran Public Training
  1. INFORMATION OPTIONS
  2. (required)
  3. (required)
  4. PERSONAL DATA
  5. (required)
  6. (required)
  7. (required)
  8. (valid email required)
  9. (required)
  10. (required)
  11. PRE REGISTRATION DATA (Tidak Mengikat)
  12. (required)
  13. MESSAGE FOR TRAINING PROVIDER
 

cforms contact form by delicious:days

Share and Enjoy: These icons link to social bookmarking sites where readers can share and discover new web pages.
  • TwitThis
  • Facebook
  • LinkedIn
  • Google Bookmarks
  • Y!GG
  • Digg
  • del.icio.us
  • StumbleUpon
  • Reddit
  • MySpace
  • Technorati
  • YahooMyWeb
  • YahooBuzz

About the Author:

http://www.twitter.com/avisdjamal

Post a Comment