AC/ DC Electrical Motor

Training AC/ DC Electrical Motor ini membantu peserta memahami prinsip dasar elektronika daya dalam drive menggunakan konverter mode sakelar

Yogyakarta/ Semarang/ Solo | 11 – 12 Mei 2020 | Rp 6.900.000,-
Bandung/ Jakarta/ Surabaya | 02 – 03 Juni 2020 | Rp 7.900.000,-
Bali/ Batam/ Balikpapan/ Manado/ Lombok | 06 – 07 Juli 2020 | Rp 8.900.000,-
Online Training Available | Date and Fee at Proposal – PASTI JALAN

Jadwal Training 2020 Selanjutnya …

 

 

Deskripsi Training AC/ DC Electrical Motor

This course covers AC/ DC electrical motor drives for speed/position control.  It presents an integrated discussion of AC/ DC electric motor, power electronics, and control systems. Applications of electric drives can be found in industries, electric transportation, robotics, process control and energy conservation. This course gives a thorough understanding of AC/DC electrical motor’s working, control , protection, maintenance, failure modes and the tools to maintain and troubleshoot AC/ DC electrical motors drives. The course focuses on the dc and ac motor from solid state converters for better torque and speed response. Advanced control techniques are applied to optimize the performance of dc/ac motor drives. Since majority of modern drives are dc/ac motor drives, the course centers around the control of dc/ac motor drives.

Participant will gain a fundamental understanding of the  AC/ DC electrical motor drives, installation, operation and troubleshooting. Participant will gain valuable insight into the selection of the protection necessary to ensure your motors are protected against fault conditions, so as to ensure reliability and long life.  Finally, control aspects of some special motors, such as permanent magnet synchronous motor, brushless dc motor, switched reluctance motor, etc. Computer simulations are used for understanding AC/DC electric motor, power-electronics based converters and the design of control systems.

 

Tujuan Kegiatan Training AC/ DC Electrical Motor

After successfully completing this course, Participants will able to do the following:

  1. Understand the AC/DC electrical motor drives basic principles
  2. Describe the Electric Drive systems and various applications such as flexible production systems, industries, transportation, robotics and process control.
  3. Understand the principle on AC/ DC electrical motor.
  4. Understand the basic principles of power electronics in drives using switch-mode converters and pulse width modulation.
  5. Design torque, speed, and position controllers of motor drives.
  6. Explain operating principles, major components and control logic used with AC and DC drive speed controls.
  7. Learn the stepper motors and switched-reluctance motor drives.
  8. Get an appreciation of power quality issues in powering electric drives.
  9. Compare the advantages and disadvantages of AC DC drives based on application.
  10. Discuss the advantages of using variable speed drives in constant torque and variable horsepower loads.
  11. Understand the Troubleshoot  of AC/ DC electrical motor drives.

 

Materi Training AC/ DC Electrical Motor

  1. Introduction to AC/DC electrical motor drives.
  2. Basic principles of electro-mechanical energy conversion (Efficiency, torque, inertia, horsepower/power factor, Torque-speed curves)
  3. Principles of AC electrical motor (operating system and control)
  4. Principles of DC electrical motor (operating system and control)
  5. Basic understanding of switch-mode power electronic converters in electric drives.
  6. DC-motor drives and electronically-commutated motor drives.
  7. DC motor drives  (Speed-torque characteristics DC shunt,  series, Speed and position control methods)
  8. Designing feedback controllers for motor drives.
  9. Introduction to AC machines.(Induction-synchronous motors)
  10. Induction-motor drives: speed control.
  11. Vector control of induction-motor drives.
  12. Reluctance drives: stepper-motor and switched-reluctance drives.
  13. Energy efficiency of electric drives and inverter-motor interactions.
  14. Powering electric drives: power quality issues.
  15. Ancillary issues in drives: sensors and  controllers.
  16. Converters and control (Phase controlled converters,  Four quadrant operation Choppers,  AC to DC converters)
  17. Inverters and PWM techniques
  18. Voltage source inverters, current source inverters and PWM techniques
  19. Power Quality issue: Harmonic elimination
  20. Advance induction motor control (constant flux speed control ,vector control)
  21. Troubleshoot AC/ DC electrical motor drives

 

Jadwal Training 2020

Hotel Santika Kuta, Bali
Hotel Nagoya Plaza, Batam
Hotel Fave, Balikpapan
Hotel Aston, Manado
Hotel Lombok Raya, Mataram
Hotel Serela Merdeka, Bandung
Hotel Santika Pandegiling, Surabaya
Sofyan Hotel Betawi, Jakarta
Hotel Ibis, Solo
Hotel Ibis Simpang Lima, Semarang
Hotel Ibis Malioboro, Yogyakarta

  • 11 – 12 Mei 2020
  • 2 – 3 Juni 2020
  • 8 – 9 Juni 2020
  • 15 – 16 Juni 2020
  • 22 – 23 Juni 2020
  • 29 – 30 Juni 2020
  • 6 – 7 Juli 2020
  • 13 – 14 Juli 2020
  • 20 – 21 Juli 2020
  • 27 – 28 Juli 2020
  • 3 – 4 Agustus 2020
  • 10 – 11 Agustus 2020
  • 18 – 19 Agustus 2020
  • 24 – 25 Agustus 2020
  • 31 Agustus 2020 – 1 September 2020
  • 7 – 8 Sepember 2020
  • 14 – 15 September 2020
  • 21 – 22 September 2020
  • 28 – 29 September 2020
  • 5 – 6 Oktober 2020
  • 12 – 13 Oktober 2020
  • 19 – 20 Oktober 2020
  • 26 – 27 Oktober 2020
  • 2 – 3 November 2020
  • 9 – 10 November 2020
  • 16 – 17 November 2020
  • 23 – 24 November 2020
  • 30 November 2020 – 1 Desember 2020
  • 7 – 8 Desember 2020
  • 14 – 15 Desember 2020
  • 21 – 22 Desember 2020
  • 28 – 29 Desember 2020

 

Investasi & Fasilitas

2020 – (Non Residential, Belum Terasuk Pajak PPn 10%)

  • Rp 8.900.000 untuk lokasi di Bali, Batam, Balikpapan, Manado atau Lombok
  • Rp 7.900.000 untuk lokasi di Bandung, Jakarta atau Surabaya
  • Rp 6.900.000 untuk Lokasi Solo, Semarang atau Yogyakarta
  • Jika Perusahaan/ Instansi mengirimkan lebih dari satu peserta pada judul dan tanggal yang sama maka akan di berikan potongan harga pada peserta kedua dan seterusnya masing – masing sebesar Rp 1.000.000 per peserta
  • Quota minimum 2 peserta
  • Quota minimum 3 peserta (Untuk Manado, Balikpapan dan Lombok Quota minimal 4 peserta)
  • Fasilitas: Certificate, Training kits, USB, Lunch, Coffe Break, Souvenir
  • Untuk peserta luar kota disediakan transportasi antar-jemput dari Bandara/ Stasiun ke Hotel khusus bagi perusahaan yang mengirimkan minimal 3 orang peserta)

 

Instruktur Training

Tugino, ST MT & Team

 

AC/ DC ELECTRICAL MOTOR

Formulir Permintaaan Informasi Lanjutan / Pra-Pendaftaran Public Training
  1. INFORMATION OPTIONS
  2. (required)
  3. (required)
  4. PERSONAL DATA
  5. (required)
  6. (required)
  7. (required)
  8. (valid email required)
  9. (required)
  10. (required)
  11. PRE REGISTRATION DATA (Tidak Mengikat)
  12. (required)
  13. MESSAGE FOR TRAINING PROVIDER
  14. Captcha
 

cforms contact form by delicious:days