PRODUCTION OPERATION AND PROBLEM SOLVING

PRODUCTION OPERATION AND PROBLEM SOLVING
Hotel Holiday Inn,  Bandung | 2 – 4 Juli  2013 | IDR  8.750.000,- /Participant

 

 

 

SASARAN BELAJAR :
Setelah menyelesaikan kursus ini diharapkan peserta dapat :

• Memahami prinsip-prinsip dasar perhitungan dan melakukan optimisasi pada saat operasi produksi sumur-sumur minyak, gas dan reservoir panas bumi dilaksanakan, pengembangan pelaksannaan optimisasi produksi ini untuk meningkatkan kinerja produksi sumuran dan lapangan.
• Melakukan diagnosis sederhana dan memengerti penyelesaian permasalahan dalam operasi produksi sumur-sumur minyak dan bas bumil.
• Membuat analisis sederhana terhadap data sumuran minyak, gas dan panas bumi ,melakukan peramalan kinerja dan merencanakan pengembangn operasi produksi
• Melakukan perhitungan-perhitungan kuantitatip sederhana dari seluruh data perolehan data tubing, flowline, choke, perforasi, gravel-pack, sub-surface savety valve pada sumuran, merencanakan pengembangannya dengan memperhitungan kemampuan masing-masing sumuran.
• Mempergunakan pengetahuan operasi produksi untuk keperluan penyelesaian permasalahan sumur seperti : pada saat penyemenan, penanganan scale, pasir, korosi dan damage yang mungkin terjadi pada sumuran minyak dan gas bumi.
• Memahami prinsip-prinsip dasar perancangan : penyemenan, workover, stimulasi sumuran dengan  pengasaman dan perekahan hidrololik, perencanaan work over dan lain-lain

PRE-REQUISITE :
Latar belakang  : Operator, Senior Operator, Engineer/Non Engineer

MATERI KURSUS :

• Geologic Considerations in producing Operation

• Introduction
• Sandstone Reservoirs
• Geologic Factors Affecting Reservoir Properties in Sandstone
• Application of Geologic concepts in Specific Sandstone
• Carbonate Reservoirs
• Application of Geologic Concepts in Carbonate Reservoirs

• Reservoir Considerations in Well Completions

• Introduction
• Hydrocarbon Properties of Oil and Gas
• Recommendations of Obtaining Good Test Data
• “Eyeball” Interpretation of Pressure Charts

• Primary Cementing

• Introduction
• Cementing Materials
• Cement Additives
• Cement Bonding
• Flow Properties of Primary Cements
• Displacement Mechanics
• Cost of Primary Cementing
• Special Problem Situations-New Developments
• Primary Cementing Practices

• Well Completion Design

• Factors Influencing Well Completion Design
• Conventional Tubular Configuration
• Unconventional Tubular Configurations
• Sizing Production Tubular
• Completion Interval
• Permanent Well Completions (PWC)
• Tubingless Completion

• Tubing Strings,Packers,Subsurface Control Equipment

• Tubing Strings
• Steel Grades
• Tubing Connections
• Makeup of API Threaded connection
• Design of Tubing Strings
• High Strength Tubing
• Physical Properties of Steel
• Sensitivities of High Strength Tubing
• Tubing Inspection
• Tubing Handling Practices
• Equipment for Use With-Strength Tubing
• Tubing Running Practices
• API Publication List
• Packers and Subsurface Control Equipment
• Production Packers
• Subsurface Control Equipment

• Perforating Oil and Gas Wells

• Introduction
• Types of Perforators
• Evaluation of Perforator Performance
• Factors  Aftecting Gun Perforating Results
• Perforating in a Clean Fluid with Differential Pressure Into Wellbore
• A Comparison between the GEO-VANN System and Other Perforating Methods in Wells Equipped with Packers

• Completion and Workover Fluids

• Functions-Requirements-Selection Criteria
• Formation Damage Related to Solids
• Oil Fluids-Practical Application
• Conventional Water-Base Mud
• Oil Base or Invert-Emulsion Muds
• Foam
• Perforating Fluids
• Packer Fluids
• Well Killing

• Through-Tubing Production Logging

• Introduction
• Logging Device
• Application of Through-Tubing Production logging
• Field Examples of Production Logging Techniques
• Primary Cement Evaluation

• Problem Well Analysis

• Problem Wells
• Problem Well Analysis Checklist

• Parafin and Asphaltene

• Introduction
• Paraffin and Asphaltene Chemistry
• Deposition Mechanisms
• Removal of Wax Deposits
• Preventing or Decreasing Wax Deposition
• Design of Wax Control

• Squeeze Cementing-Remedial Cementing

• Introduction
• Theoretical Considerations
• Practical Considerations
• Special Squeeze Cementing Situations
• Planning a Squeeze Cement Job
• Normal Operational Procedures
• Other Operational Procedures
• Plug-Back Operations
• Special Cement Systems

• Sand Control

• Introduction
• Reduction of Drag Force
• Mechanical Methods of Sand Control
• Practical Considerations in Gravel Packing
• Use of screen Without Gravel
• Resin Consolidation Methods

• Formation Damage

• Introduction
• Basic Causes of Damage
• Classification of Damage Mechanisms
• Reduced Absolute Permeability
• Increased Fluid Viscosity (Emulsion)
• Diagnosis of Formation Damage

• Surfactants for Well Treatments

• Characteristics of Surfactants
• Use and Action of Surfactant
• Formation Damage Susceptible to Surfactant Treatment
• Preventing or Removing Damage
• Well Stimulation With Surfactants
• Increasing Effectiveness of Rod Pumping
• Prevention of Well Damage

• Acidizing

• Acids Used in Well Stimulation
• Acid Additives
• Carbonate Acidizing
• Acidizing Techniques for Caronat Formations
• Sandstone Acidizing
• Potential Safety Hazard in Acidizing

• Hydraulic Fracturing

• Introduction
• Mechanics of Fracturing
• Production Increase from Fracturing
• Propping the Fracture
• Frac Fluids
• Frac Job Design
• Frac Job Evaluation Techniques

• Scale Deposition,Removal,and Prevention

• Introduction
• Causes of Scale Deposition
• Prediction and Identification of Scale
• Scale Removal
• Scale Prevention

• Corrosion Control

• The Corrosion Process
• Detection and Measurement of Corrosion
• Corrosion Control

INSTRUKTUR :
1.     Dr.Ir. Sudjati Rachmat, DEA

ASISTEN :
1.     Ir. Gilang Erlangga

VANUE AND DATE
Vanue  :
Hotel Holiday Inn,  Bandung

Date :

• 29 – 31 Mei  2013  ( Batch I )
• 2 – 4 Juli  2013 ( Batch II)

INVESTATION

• IDR  8.750.000,- /Participant Non residential.
• Fir send 3 participant from the same company IDR. 8.250.000,-/participant.

FACILITIES

• Training Kit
• Soft Copy Material Training On Flashdisk 4GB.
• Coffee Break & Lunch
• Certifikat
• Souvenir
• Additional Program (optional)

Formulir Permintaaan Informasi Lanjutan / Pra-Pendaftaran Public Training

1. INFORMATION OPTIONS
2. Judul Training(required)
3. Tanggal Training
4. Select a message type Registration Offering Letter (Permintaan Proposal Penawaran) Next Schedule Information (Jadwal selanjutnya) More Information (Informasi tambahan) Others (lain-lain) (required)
5. PERSONAL DATA
6. Your Name(required)
7. Job Title(required)
8. Company(required)
9. Company Address
10. Email(valid email required)
11. Mobile Phone(required)
12. Office Phone(required)
13. Extention No.
14. Facsimile (Fax)
15. Website
16. PRE REGISTRATION DATA (Tidak Mengikat)
17. Penanggung Jawab Training di Perusahaan
18. Email
19. Office Phone+Ext atau No. Handphone
20. Jumlah Peserta(required)
21. Nama-nama peserta
22. Payment Method Bank Transfers Submitting an Invoice Cheque or Cash on arrival ( If Possible)
23. MESSAGE FOR TRAINING PROVIDER
24. Pesan untuk penyelenggara Training
25. CC this registration / message to me
26. Isikan angka/huruf pada gambar

 

cforms contact form by delicious:days